N.B: Decal kit cannot be returned or exchanged.
A new decal kit is perhaps the most affordable way to make your bike look like new again. With the stylish asymmetrical pattern, you will get some envious sideways glances as you ride!
The decal kit consists of the following parts:
• Radiator shrouds
• Tank (depending on model)
• Front fender
• Rear fender
• Fork leg protection
• Number plate
• Side panels/Air can
• Swingarm
IMPORTANT! If your decal kit contains a tank decal, it must be perforated! Otherwise, there is a high risk that air bubbles will form due to petrol fumes. This is easily done with a razor blade BEFORE mounting.
You cannot exactly match the colours of the decals with the colour of the original plastics!
The decals are manufactured in JT Racing’s own state-of-the-art printing plant and are of the highest quality.
After the decal has been printed with digital printing, it is laminated with a very strong and transparent plastic material that protects against wear.
After this, an acrylate-based glue is applied which causes the decals to stick hard while being removable without leaving glue residue on the covers.
Installation of decal kit:
Be sure to clean your plastic thoroughly first. Pre-decal cleaner gives the best results but brake cleaner also works.
This also applies to new plastics, which have oil residues on the surface after manufacture.
The decals should be mounted at room temperature.
Make sure that the decal is well centered on the plastic before you start pasting it. When you are satisfied with the fit, remove the protective film from one corner of the decal and then start to press the decal down firmly.
It is good to have a small cloth/sponge to press down with that easily slides over the decal.
Carefully move forward in straight lines as you press down gently to avoid air bubbles.
For the curved/shaped decals, you can heat the decal gently with a hair dryer/heat gun to make it more pliable.
After mounting, allow the plastic to rest for 24 hours at room temperature before riding to ensure the decals are properly attached.
A new decal kit is perhaps the most affordable way to make your bike look like new again. With the stylish asymmetrical pattern, you will get some envious sideways glances as you ride!
The decal kit consists of the following parts:
• Radiator shrouds
• Tank (depending on model)
• Front fender
• Rear fender
• Fork leg protection
• Number plate
• Side panels/Air can
• Swingarm
IMPORTANT! If your decal kit contains a tank decal, it must be perforated! Otherwise, there is a high risk that air bubbles will form due to petrol fumes. This is easily done with a razor blade BEFORE mounting.
You cannot exactly match the colours of the decals with the colour of the original plastics!
The decals are manufactured in JT Racing’s own state-of-the-art printing plant and are of the highest quality.
After the decal has been printed with digital printing, it is laminated with a very strong and transparent plastic material that protects against wear.
After this, an acrylate-based glue is applied which causes the decals to stick hard while being removable without leaving glue residue on the covers.
Installation of decal kit:
Be sure to clean your plastic thoroughly first. Pre-decal cleaner gives the best results but brake cleaner also works.
This also applies to new plastics, which have oil residues on the surface after manufacture.
The decals should be mounted at room temperature.
Make sure that the decal is well centered on the plastic before you start pasting it. When you are satisfied with the fit, remove the protective film from one corner of the decal and then start to press the decal down firmly.
It is good to have a small cloth/sponge to press down with that easily slides over the decal.
Carefully move forward in straight lines as you press down gently to avoid air bubbles.
For the curved/shaped decals, you can heat the decal gently with a hair dryer/heat gun to make it more pliable.
After mounting, allow the plastic to rest for 24 hours at room temperature before riding to ensure the decals are properly attached.